Please Support by checking out some of the sponsors to the right

Wednesday, March 18, 2009

Difference between lserver and server in nslookup

There are little chores you'll come to use nslookup for almost every day: finding the IP address or MX records for a given domain name, or querying a particular name server for data. We'll cover these first, before moving on to the more occasional stuff.

12.5.2. Authoritative Versus Nonauthoritative Answers

If you've used nslookup before, you might have noticed something peculiar -- the first time you look up a remote domain name, the answer is authoritative, but the second time you look up the same name it is nonauthoritative. Here's an example:

% nslookup
Default Server: relay.hp.com
Address: 15.255.152.2

> slate.mines.colorado.edu.
Server: relay.hp.com
Address: 15.255.152.2

Name: slate.mines.colorado.edu
Address: 138.67.1.3

> slate.mines.colorado.edu.
Server: relay.hp.com
Address: 15.255.152.2

Non-authoritative answer:
Name: slate.mines.colorado.edu
Address: 138.67.1.3
While this looks odd, it really isn't. What's happening here is that the first time the local name server looks up slate.mines.colorado.edu, it contacts the name server for mines.colorado.edu, and the mines.colorado.edu server then responds with an authoritative answer. The local name server, in effect, passes the authoritative response directly back to nslookup. It also caches the response. The second time you look up slate.mines.colorado.edu, the name server answers out of its cache, which results in the answer "non-authoritative." [96]
[96]BIND 9 name servers, interestingly, show even the first responses as nonauthoritative.

Notice that we terminated the domain name with a trailing dot each time we looked it up. The response would have been the same if we'd left the trailing dot off. There are times when it's critical that you use the trailing dot while debugging, and times when it's not. Rather than stopping to decide if this name needs a trailing dot, we always add one if we know the name is fully qualified, except, of course, if we've turned off the search list.

12.5.3. Switching Name Servers

Sometimes you want to query another name server directly -- you may think it is misbehaving, for example. You can switch servers with nslookup by using the server or lserver command. The difference between server and lserver is that lserver queries your "local" name server -- the one you started out with -- to get the address of the server you want to switch to; server uses the default name server instead of the local server. This difference is important because the server you just switched to may not be responding, as we'll show in this example:

% nslookup
Default Server: relay.hp.com
Address: 15.255.152.2
When we start up, our first name server, relay.hp.com, becomes our lserver. This will matter later on in this session.

> server galt.cs.purdue.edu.
Default Server: galt.cs.purdue.edu
Address: 128.10.2.39

> cs.purdue.edu.
Server: galt.cs.purdue.edu
Address: 128.10.2.39

*** galt.cs.purdue.edu can't find cs.purdue.edu.: No response from server
At this point, we try to switch back to our original name server. But there is no name server running on galt.cs.purdue.edu to look up relay.hp.com's address:

> server relay.hp.com.

*** Can't find address for server relay.hp.com.: No response from server
Instead of being stuck, though, we use the lserver command to have our local name server look up relay.hp.com's address:

> lserver relay.hp.com.
Default Server: relay.hp.com
Address: 15.255.152.2

> ^D
Since the name server on galt.cs.purdue.edu did not respond -- that host isn't even running a name server -- it wasn't possible to look up the address of relay.hp.com to switch back to using relay 's name server. Here's where lserver comes to the rescue: the local name server, relay, was still responding, so we used it. Instead of using lserver, we also could have recovered by using relay's IP address directly -- server 15.255.152.2.

You can even change servers on a per-query basis. To specify that you'd like nslookup to query a particular name server for information about a given domain name, you can specify the server as the second argument on the line, after the domain name to look up, like so:

% nslookup
Default Server: relay.hp.com
Address: 15.255.152.2

> saturn.sun.com. ns.sun.com.
Name Server: ns.sun.com
Address: 192.9.9.3

Name: saturn.sun.com
Addresses: 192.9.25.2

> ^D
And, of course, you can change servers from the command line. You can specify the server to query as the argument after the domain name to look up, like this:

% nslookup -type=mx fisherking.movie.edu. terminator.movie.edu.
This instructs nslookup to query terminator.movie.edu for MX records for fisherking.movie.edu.

Finally, to specify an alternate default name server and enter interactive mode, you can use a hyphen in place of the domain name to look up:

% nslookup - terminator.movie.edu.
See Also: NsLookup ommand explained in detailOriginal Article Source Here

No comments:

Post a Comment